FOX3 T 301

概述

Extron FOX3 T 301 光纤发送器通过光纤长距离传输符合 HDCP 标准的 HDMI 视频、USB、音频、控制和 3D 同步信号。其设计着力于出色的高分辨率图像性能，它采用 Extron 全数字化技术，可通过两根光纤完美地传输像素级无压缩的分辨率高达 4K/60 @ 4:4:4 的图像，或通过单根光纤传输数学无损的 4K/60 @ 4:4:4 视频信号。USB 端口支持 USB 3.0 至 1.0 设备，而 USB HID 端口的设备类型过滤功能则可将其限定为仅支持 HID。专门设计用于视音频和 KVM 系统的发送器还包括许多易于集成的特性，如密钥管理器 (Key Minder®)、EDID 管理器 (EDID Minder®)、音频加嵌、以太网监视和控制、音频增益和衰减以及实时的系统监控。

主要特性

• 通过光纤发送 HDMI 视频、USB、立体声音频、RS-232 控制、红外控制和 3D 同步信号
• 通过单根光纤传输分辨率高达 4096x2160/60 Hz、带 4:4:4 色度取样的数学无损 4K 视频信号
• 通过两根光纤传输分辨率高达 4096x2160/60 Hz、带 4:4:4 色度取样的无压缩 4K 视频信号
• 支持 HDMI 2.0 参数标准，包括高达 18 Gbps 的数据速率、高达 12 位的色深和 3D
• 符合 HDCP 2.3 标准
• 支持 USB 2.0 至 1.0 设备，并兼容可运行数据速率高达 480 Mbps USB 2.0 的 USB 3.0 设备
• 所有特性

技术参数

也请参阅我们的  PDF 格式的技术参数

FOX3 T 301/311
specification
Frame rate3	24, 25, 30, 50, or 60 fps
Chroma sampling3	4:4:4, 4:2:2
Color bit depth2,3	8, 10, or 12 bits per color
Signal Type	HDMI 2.0, HDCP 2.3
Max. video data rate	18.0 Gbps
NOTE     1Supports lossless 4K video over one fiber or uncompressed 4K video over two fibers. 2Supports 12-bit color bit depth for uncompressed 4K video over two fibers. When using a FOX3 SR scaling receiver, the scaler must be in bypass mode to pass 4K video with a 12-bit color bit depth. 3Subject to the maximum data rate limit. Use our calculator at www.extron.com/8Kdatarate to determine video parameters supported by this data rate.
NOTE     This product contains Class 1 laser. It meets the safety regulation of IEC 60825-1, FDA 21 CFR 1040.10, and FDA 21 CFR 1040.11.
Optical fiber interconnection between transmitter and receiver
Number/type	1 or 2 SFPs
Connectors	1, 2, or 3 LC connectors
Operating distance
Singlemode	20 km (12.4 miles) with singlemode (SM) cables
Multimode	500 m (1640 feet) with 50 µm OM4 4700 MHz bandwidth laser optimized multimode cables
NOTE     The system works with OM1, OM2, and OM3 fiber at reduced distances.
NOTE     Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks.
Nominal peak wavelength	850 nm for multimode, 1310 nm for singlemode
Data rate	10.0 Gbps (1 fiber) or 20.0 Gbps (2 fibers)
Transmission power
Singlemode	-5.2 dBm, minimum
Multimode	-2.8 dBm, minimum
Maximum receiver sensitivity
Singlemode	-12.6 dBm, maximum
Multimode	-11.1 dBm, maximum
Optical loss budget
Singlemode	+7.4 dB, maximum
Multimode	+8.3 dB, maximum
Video
Maximum data rate	18.0 Gbps (6.0 Gbps per color)
Maximum pixel clock	594 MHz
Resolution range	640x4808 up to 4096x21601,2,3,4,5,6,7,8, ​480p7,8, 576p6, 720p3,4,5,6,7,8,9, 1080i6,7,8, 1080p1,2,3,4,5,6,7,8,9, 2K1,2,3,4,5,6,7,8, ​3840x21601,2,3,4,5,6,7,8, 4096x21601,2,3,4,5,6,7,8 123.98 Hz, 224 Hz, 325 Hz, 429.97 Hz, 530 Hz, 650 Hz, 759.94 Hz, 8​60 Hz, 9120 Hz
Frame rate	24, 25, 30, 50, 60, or 120 fps
Color space	4:4:4, 4:2:2
Color bit depth	8, 10, and, 12 bits per color
Standards	HDMI 2.0, HDCP 2.3
Horizontal frequency	24 kHz to 135 kHz for resolutions up to 18 Gbps
Vertical frequency	24 Hz to 120 Hz for resolutions up to 18 Gbps
Format	RGB and YCbCr digital video
NOTE     HDMI protocol exceptions: Consumer Electronics Control (CEC) signaling across the HDMI interface is not supported. Ethernet signal transport is not supported (HDMI pin 14 is not connected). ​Return Audio channel (ARC) is not supported (HDMI pin 14 is not connected).
Video input and loop out
Number/signal type	1 HDMI input 1 HDMI loop out
Connectors	1 female HDMI input type A 1 female HDMI loop out type A
Power for active cables	1.1 W max. for the HDMI port
Audio
Gain	Unbalanced output: -6dB; balanced output: 0 dB (default)
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	<0.1% @ 20 Hz to 20 kHz at nominal level
S/N	>90 dB at maximum output (unweighted)
CMRR	65 dB @ 20 Hz to 20 kHz
Stereo channel separation	>80 dB @ 1 kHz
Bit depth	16, 20, 24
Sampling rate	48 kHz
Audio input
Number/signal type	1 digital audio, de-embedded from HDMI or 1 analog stereo, balanced/unbalanced
Connectors	1 female HDMI (shared with video input) (1) 3.5 mm captive screw connector, 5 pole
Impedance	≥10 k ohms unbalanced, ≥20 k ohms balanced
Nominal level	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level	+21  dBu balanced, +15 dBu unbalanced
Source formats	2 CH LPCM
Gain range	Adjustable, - 18 dB to +24 dB, 1 dB steps
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio return output
Number/signal type	1 analog stereo, balanced/unbalanced
Connectors	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced; 100 ohms balanced (analog only)
Maximum level (Hi-Z)	+21 dBu balanced, +15 dBu unbalanced
Gain error	±0.5 dB channel to channel
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Communications
USB configuration port
Number/type	1 front panel mini USB B, female
Standard	Ethernet over USB
Serial host control port
Control	1 RS-232, 3.5 mm captive screw connector, 5-pole (3 pins are used), rear panel
Pass-through	1 RS-232, 3.5 mm captive screw connector, 5-pole (3 pins are used), rear panel
Baud rate and protocol
Control	9600 baud, 8 data bits, 1 stop bit, no parity
Pass-through	9600 to 115,200 baud
Serial control pin configuration	Captive screw: 1 = Tx, 2 = Rx, 3 = GND
IR control port	(1) 3.5 mm captive screw connector, 5 pole (connector is shared with RS-232 pass thru) TTL level (0 to 5V) modulated infrared control from 30 kHz to 56 kHz
IR control pin configuration	3 = GND, 4 = IR Tx, 5 = IR Rx
Ethernet control
Ethernet port	1 RJ-45 connector, female
Ethernet data rate	10/100/1000Base-T, half/full duplex with autodetect
Protocols	ARP, ICMP (ping), DHCP, DNS, HTTPS, SFTP, SSH, TCP/IP, UDP/IP
Default settings	Link speed and duplex level = autodetected IP address = 192.168.254.254 Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 DHCP = off
Program control	Extron Product Configuration Software Extron Simple Instruction Set (SIS™)
USB extension
Standards	USB 2.0 (FOX3 T 301 models only), USB 1.1
Host support	xHCI (USB 3.2 Gen 1/2, USB 3.1 Gen1/2, USB 3.0) (FOX3 T 301 models only),  EHCI (USB 2.0) (FOX3 T 301 models only), OHCI/UHCI (USB 1.1)
Data rates	Low speed (1.5 Mbps), full speed (12 Mbps),  high speed (480 Mbps) (FOX3 T 301 models only)
Data transfer types	Bulk, control, interrupt, and isochronous
NOTE     ​Extron strongly recommends compatibility testing while designing, and before installing, any system that includes a USB camera. There are several unique transport methods in use by USB camera manufacturers and the level of support is governed by this. Please contact an Extron Applications Engineering for more information.
USB host ports
FOX3 T 301
Number/signal type	1-port USB HID 1-port USB 2.0
Connectors	2 USB type B, female
Maximum built-in USB hubs	0
Minimum built-in USB hubs	0
FOX3 T 311
Number/signal type	1-port USB HID
Connector	1-port USB type B, female
Maximum built-in USB hubs	0
Minimum built-in USB hubs	0
NOTE     When configured endpoint to endpoint, there are 0 hubs. When configured with a FOX3 Matrix, there is 1 hub.
General
Power supply	Internal Input: 100-240 VAC, 50-60 Hz
Power consumption	23.3 watts
Ambient temperature/humidity	Storage: -40 to +158°F (-40 to +70°C) / 10% to 90%, noncondensing Operating: +32 to +122°F (0 to +50°C) / 10% to 90%, noncondensing
Cooling	Fan, air flows from front to rear (vented)
Thermal dissipation	78.3 BTU/hr
Mounting
Rack mount	Yes, with optional rack shelf
Furniture mount	Yes, with optional under desk mounting kit
Enclosure type	Metal
Enclosure dimensions	1.7" H x 8.75" W x 8.5" D (half rack wide) (4.4 cm H x 22.2 cm W x 21.6 cm D) (Depth excludes connectors.)
Product weight	2.4 lbs (1.1 kg)
Regulatory compliance	CE, c-UL, C-tick, FCC Class A, ICES, UL, VCCI Complies with the appropriate requirements of RoHS, WEEE.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(6333-D8)