DTP T HWP 4K 331 D

概述

Extron DTP T HWP 4K 331 D 是一单元 Decorator 型长距离型发送器，可通过单根 CATx 屏蔽电缆将 HDMI、音频以及双向 RS-232 和红外信号发送至 100 m (330') 远的 Extron DTP® 330 功能产品。其一单元规格尺寸可最大化节省空间，适合安装在墙面、地插盒和家具等应用环境。DTP T HWP 4K 331 D 可接受模拟立体声音频信号，并通过同一根屏蔽双绞线电缆同时进行传输。它支持分辨率高达 4K 的视频信号。它还具有远程供电功能以及用于远程视音频设备控制的双向 RS-232 和红外直通。DTP T HWP 4K 331 D 的一单元可墙面安装式设计使之能够根据需要方便、准确地进行输入连接。

主要特性

• 通过单根 CATx 屏蔽电缆传输 HDMI 以及控制和模拟音频信号至 100 m (330') 远的距离
• 支持分辨率高达 4K 的计算机和视频信号
• 强烈建议使用 Extron XTP DTP 24 屏蔽双绞线电缆，以达到最佳的性能表现
• 兼容 CATx 屏蔽双绞线电缆
• 接受额外的模拟立体声音频信号
• 提供经 DoDIN APL 认证的产品
• 所有特性

技术参数

也请参阅我们的  PDF 格式的技术参数

DTP T HWP 4K 331 D
specification
Frame rate1	24, 25, 30, 50, or 60 fps
Chroma sampling1	4:4:4, 4:2:2, or 4:2:0
Color bit depth1	8 bits per color
Signal Type	HDMI 1.4, HDCP 2.3
Max. video data rate	10.2 Gbps (3.4 Gbps per color)
NOTE     1Subject to the maximum data rate limit. Use our calculator (www.extron.com/8Kdatarate) to determine video parameters supported by this data rate.
Video
Maximum data rate	10.2 Gbps (3.4 Gbps per color)
Maximum pixel clock	300 MHz
Resolution range	Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz, 4K/UHD @ 60 Hz with 4:2:0 chroma subsampling (*Reduced blanking)
Color bit depth	8, 10, or 12 bits — subject to the maximum data rate limit
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI 1.4, HDCP 2.3, CEA-861E
Video input
Number/signal type	1 single link HDMI (or DVI-D*) input
Connectors	1 female HDMI type A
NOTE     *Appropriate HDMI to DVI-D cables or adapters are required for HDMI signal input/output.
Interconnection between transmitter and receiver
Connectors	1 female RJ-45 per unit for 1 cable connecting the transmitter and receiver
Termination standards	TIA/EIA T568B
DTP signal
Signal transmission distance
1080p @ 60 Hz	Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable
2560x1600 @ 60 Hz	Up to 330' (100 m) using STP cable or XTP DTP 24 cable
4K/UHD @ 30 and 60 Hz	Up to 330' (100 m) using STP cable or XTP DTP 24 cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth STP cable
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
NOTE     Output mode signaling: DTP:            HDMI with embedded audio, analog audio, RS-232 and IR, and remote power HDBaseT:    HDMI with embedded audio plus RS-232 and IR
Audio
Gain	Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.03% @ 20 Hz to 20 kHz at maximum output
S/N	>90 dB at maximum output (15 dBu), balanced (unweighted)
Stereo channel separation	>80 dB @ 1 kHz to 20 kHz
Audio input
Number/signal type	1 stereo (2 channel), unbalanced
NOTE     Analog audio is not embedded onto the digital video signal. Analog audio and digital embedded audio are transmitted simultaneously and output on the receiver on two different connectors.
Connectors	(1) 3.5 mm stereo jack, 2 channel; tip (L); ring (R); sleeve (ground)
Impedance	>10k ohms, DC coupled
Nominal level	-10 dBV (316 mVrms)
Maximum level	+7 dBV, unbalanced
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Communications — external device (RS-232/IR over TP)
Serial control port	RS-232 via (1) 3.5 mm, 5 pole captive screw connector (connector is shared with IR control port)
NOTE     Protocol is mirrored between the connected DTP 230 or DTP 330 endpoints and the "Over TP" ports on the DTP T HWP 331 D. Signals from a control device pass into each "Over TP" port, are embedded with the DTP signal, and sent to the individual DTP 230 Tx or Rx endpoints for control of remote sink or source devices. The "Over TP" ports are simply pass-through connections to DTP endpoints.
Baud rates	Up to 115200 baud
Protocol	Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none
Serial control pin configuration	Captive screw connectors: 1 = Tx, 2 = Rx, 3 = Gnd
IR control port	(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port) TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
IR control pin configuration	3 = Gnd, 4 = IR Tx, 5 = IR Rx
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts
Power consumption
Device	3.0 watts
Device and power supply	3.9 watts
Remote power budget	12 watts
NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
Ambient temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Thermal dissipation
Device	10.0 BTU/hr
Device and power supply	13.3 BTU/hr
Mounting
Furniture or wall mount	Yes, with a 1-gang wall box or mud ring
Enclosure type	Metal
Enclosure dimensions
Faceplate	2.6" H x 1.3" W x 0.3" D (6.6 cm H x 3.3 cm W x 0.6 cm D)
Device	2.8" H x 1.7" W x 1.9" D (7.1 cm H x 4.3 cm W x 4.8 cm D)
NOTE     Overall height is 4.2" (10.7 cm), including mounting tabs. Mounting holes are 3.2" (8.2 cm) apart on center. Depth excludes connectors. Fits the opening in a 1 gang decorator wallplate).
Product weight	0.2 lbs (0.1 kg)
Regulatory compliance	AS/NZS, C-tick, c-UL, CE**, FCC Class A**, ICES, UL
NOTE     **CE and FCC testing is conducted with STP cable.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(5381-D9)