DTP2 R 211

主要特性

• 通过单根 CATx 屏蔽电缆在 100 m (330') 远的距离上接收 HDMI 以及控制和模拟音频信号
• 支持分辨率高达 4K/60 @ 4:4:4 的视频信号
• 立体声音频解嵌
• 支持 HDMI 2.0b 参数标准，包括高达 18 Gbps 的数据速率、HDR、高达 12 位的色深、3D 和高清无损的音频格式
• 符合 HDCP 2.3 标准
• DTP2 产品支持远程供电
• 所有特性

技术参数

也请参阅我们的  PDF 格式的技术参数

DTP2 R 211
specification
Frame rate1	24, 25, 30, 50, or 60 fps
Chroma sampling1	4:4:4, 4:2:2, or 4:2:0
Color bit depth1	8, 10, or 12 bits per color
Signal Type	HDMI 1.4, 2.0b; HDCP 1.4, 2.3
Max. video data rate	18 Gbps (6 Gbps per color)
NOTE     1Subject to the maximum data rate limit. Use our calculator at www.extron.com/8Kdatarate to determine video parameters supported by this data rate.
Video
NOTE     Extron strongly recommends compatibility testing while designing, and before installing, any 3D system. There are several unique 3D formats in use by source devices and display manufacturers. The level of 3D product support is governed by pixel clock, signal format, and communication between source and sink devices. Please contact an Extron Applications Engineer for more information.
Maximum data rate	18 Gbps (6 Gbps per color)
Maximum pixel clock	600 MHz
Resolution range	2560x1600 @ 60 Hz or 1080p @ 60 Hz, 12-bit color 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz,  UHD (3840x2160) @ 60 Hz
Color bit depth	8, 10, or 12 bits — subject to the maximum data rate limit
Formats	RGB and YCbCr digital video
Standards	DVI 1.0; HDMI 1.4, 2.0b; HDCP 1.4, 2.3, CEA-861-E
Video input — transmitter
Number/signal type	1 single link HDMI (or DVI-D*)
Connectors	1 female HDMI type A
Horizontal frequency	24 kHz to 135 kHz for resolutions up to 18 Gbps
Vertical frequency	24 Hz to 120 Hz for resolutions up to 18 Gbps
NOTE     *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.
Interconnection between transmitter and receiver
Connectors	1 female RJ-45 per unit
Termination standard	TIA/EIA T568B
Signal transmission distance	Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth, STP (shielded twisted pair)
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Video output
Number/signal type	1 single link HDMI (or DVI-D*)
Connectors	1 female HDMI type A
Horizontal frequency	24 kHz to 135 kHz for resolutions up to 18 Gbps
Vertical frequency	24 Hz to 120 Hz for resolutions up to 18 Gbps
Audio
Gain	Unbalanced output: 0 dBu; balanced output +6 dBu
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.03% @ 20 Hz to 20 kHz at maximum output
S/N	>90 dB, at maximum output (15 dBu), balanced (unweighted)
Stereo channel separation	>80 dB @ 1 kHz to 20 kHz
Audio input
Number/signal type	1 PC level stereo, unbalanced 1 Digital Embedded Audio on HDMI
NOTE     Analog audio can be configured for embedding onto the digital video signal at the Transmitter. Embedded digital audio can be (configured) de-embedded from the digital video signal at the Receiver end.
Connectors	(1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) (1) Female HDMI
Impedance	>10k ohms, DC coupled
Nominal level	-10 dBV (316 mVrms)
Maximum level	+7 dBV (unbalanced)
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output
Number/signal type	1 stereo (2 channel), balanced/unbalanced
Connectors	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±0.1 dB channel to channel
Maximum level (600 ohm)	>+11 dBu, balanced
Communication — external device (pass-through, unidirectional or bidirectional)
Serial control port input/output	1 set of proprietary signals on a female RJ-45 jack
Serial control port output/input	RS-232 via a 3.5 mm, 3 pole captive screw connector
Baud rate and protocol	300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = Gnd
IR control port	(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port) TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
IR control pin configuration	3 = Gnd, 4 = IR Tx, 5 = IR Rx
General
Power supply	External (included with Tx) Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 Watts
Power consumption
Device	6.1 watts
Device and power supply	7.7 watts
Remote power budget	18 watts
NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
NOTE     DTP2 devices can only send power to other DTP2 devices. DO NOT send power to DTP devices or they will be damaged.
Ambient temperature/humidity	Storage: -40 to +158°F (-40 to +70°C) / 10% to 90%, noncondensing Operating: +32 to +122°F (0 to +50°C) / 10% to 90%, noncondensing
Cooling	Convection, vents
Thermal dissipation
Device	19.6 BTU/HR
Device and power supply	25.1 BTU/HR
Mounting
Rack mount	Yes, with optional 1U high rack shelf
Furniture mount	Yes, with optional under-desk mounting kit
Enclosure type	Metal
Enclosure dimensions	1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connectors.)
Product weight	0.529 lb (0.240 kg)
Regulatory compliance	CE, C-Tick, FCC Class A, ICES, VCCI, KCC, c-UL, RoHS, UL UL rated for use in plenum airspaces: meets UL for heat and smoke release, excluding the power supply.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(5982-D6)